When I was nerding, I was complaining about the amount of effort I was going through to just display a line of text with proper word wrapping. I introduce you to, QTextLayout
which does exactly that. I’m in the process of debugging the newly re-written code.
3 steps forward, two steps back. Regardless, I feel better about it.
On the other hand, I started reading the transcript of Delaware State Sportsmens Association Inc v. Delaware Department of Safety and Homeland Security, 23-1633, (3rd Cir. Mar 25, 2024) ECF No. 118. My blood pressure went up. I’ll be reading the rest of it and presenting some feedback. Suffice to say, the judges in the case asked questions that indicate that they have reading comprehension issues.
The left is busy screaming that Justice Thomas has no business hearing a case regarding the persecution of the J6 victims because his wife was “participating in the insurrection.”
Isn’t it amazing how the most heavily armed group of people in the world, showed up for the insurrection and forgot to bring their guns?
The number of J6 victims that were persecuted for having scary looking tactical gear and med kits is not surprising.
Note, I do have far too many spelling errors. “Prosecution” and “persecution” are two different words.
We are also watching the trial of Trump. If I wasn’t already sick from what they were doing to the J6 victims, I would have more sympathy for what they are doing to him.
This weekend will be “fun”. I’m going to be making a backing plate for a lathe chuck. I picked up a “chunk-o-iron” this week. 5.5in in diameter, 8.76 inches long. I should be able to get at least 3 backplates out of that. The cost of one backplate, if they made one to fit my lathe, would cost more than twice the cost of the raw stock.
This will be an adjust true collet chuck. When I’m done, it should be able to maintain 0.0002″ TIR. That is beautiful.
There are three primary types of lathe chucks. There is an “independent” chuck, a “self-centering” chuck, and then collet chucks.
The chuck is attached to a backplate which mounts on the spindle of your lathe. You machine the face of the backplate in place on your chuck. The better you do, the better your check will be centered.
When using a self-centering chuck or a collet chuck, you are stacking total indicated run out, TIR. The backplate will have some run out. By doing the final machining in place, you can reduce that greatly. You leave a boss on the face and that fits into a recess in the back of the chuck.
If that fit is very close, there is very little movement that can be done to cause run out. But there might be some.
When using an independent jaw, each jaw moves independently. Normally, that would be a four jaw chuck. By carefully measuring the run out, you can determine which jaw is the furthest from the center. You can tighten that jaw and the work will move closer to the center.
If the jaws are already tight, you can loosen the jaw on the opposite side slightly. Using this method, you can easily get your work running true (no run out) to within 0.0005.
The magic of an “adjust true” chuck is that it combines a self centering chuck or a collet chuck with an independent type of adjustment.
You put the backplate with chuck onto the spindle. You put a known quality pin in the chuck. You can now shift the front part of the chuck independently to get that very low TIR.
Using a collet chuck, you can take the work out of the chuck, do something to it, put it back in the collet. It will have the same run out as it had before.
This allows me to do some things more easily.
I’m glad you all got to laugh at my misfortune of losing some of my music. The magic of streaming music has introduced me to 1000s of songs I would never have heard otherwise.
What artist or song from your past have you listened to recently and said, “that’s horrible?” For me, it was Olivia Newton John’s “Physical”. I thought I would enjoy that blast from the past, I didn’t.
What artist or song have you discovered today that you would not have enjoyed in the past? For me, it is all the old time swing bands and Frank Sinatra.
The comments are open.
Like this:
Like Loading...